Ultra-Spill Decks®

Plus Models

Extra Rugged Spill Decks Provide Containment For Heavy Equipment, Machinery and Batteries.

This heavy duty spill containment deck is designed to catch drips, leaks and spills from drums, machinery or heavy equipment. Its low profile (4 ¼” high) makes it easy to drive equipment onto the surface during routine maintenance and repair operations.

Product Details:
  • 4 ¼ inch height
  • Spill deck is rated for loads up to 10,000 lbs. per square foot.
  • 2 and 4-drum spill deck modules can be connected together with bulkhead fittings to increase overall sump capacity. A virtually unlimited number of configurations are available.

Questions?

Technical stuff.  Inventory.  Lead times.  Local distributor.  We've got the answers.

Contact Us
Questions?

Ultra-Spill Deck Plus

Part # Description Dimensions in. (mm) Uniformly Disrtibuted Loads lbs. (kg) Containment Capacity gal. (L) Weight lbs. (kg)
2222 2-Drum Spill Deck Plus 54½ x 27¼ x 4¼ (1,384 x 692 x 108) 10,000 (4,536) per sq. ft. 17.5 (66) 56.0 (25.5)
2223 4-Drum Spill Deck Plus 54½ x 54½ x 4¼ (1,384 x 1,384 x 108) 10,000 (4,536) per sq. ft. 35 (132) 104.0 (47.5)

Options

Part # Description Dimensions in. (mm) Uniformly Distributed Loads lbs. (kg) Weight lbs. (kg)
2353 Loading Ramp 37 x 26½ x 4¼ (970 x 674 x 108) 1,000 (453.5) 78.0 (35.0)
1073 Bulkhead Fitting (Connects Decks together) 1.0 (0.5)
1131 26" T-Strip (Prevents spills from going between decks) 1.0 (0.5)
2221 Sidewall Plug (Plugs holes left when Decks are disconnected) 1.0 (0.5)

More info / Downloads

Chemical Compatibility

Care & Maintenance

Frequently Asked Questions

How do you get spillage out of the sump?  

We recommend using a pump (UltraTech part# 2345 can be used) to remove any spilled contents from the sump.  (Note:  spillage should be pumped into an approved container)

 

 

I need to add another Spill Deck to the one I already have.  How do I do that?  What do I need?  
Other than the Spill Deck, you’ll need one Bulkhead Fitting (part# 1073) and one T-Strip (part# 1131) for every 26” of Spill Deck length that is connected.  For example if you’re connecting a 4-Drum Spill Deck to another 4-Drum Spill Deck you would need two Bulkhead Fittings and two T-Strips.  If, on the other hand, you were connecting a 1-Drum Spill Deck to the short end of a 2-Drum Spill Deck, you would only need one each of the Bulkhead Fitting and T-Strip.

 

The Spill Deck that I bought previously does not have any holes to put the Bulkhead Fitting through.  Can I drill holes myself?
Yes.  All that is required is a 1 9/16” hole saw (1 ½” will also work).  On each side of the Ultra-Spill Decks are “dimpled” areas that indicate where holes are to be drilled.  Center the hole saw on the area you need to be drilled and carefully cut the hole(s) for your Bulkhead Fittings.   File or “flame” any rough or sharp edges prior to connecting. 

 

What are sidewall plugs for?  
Sidewall Plugs (part# 2221) can be used if you are no longer connecting a Spill Deck and therefore have a hole that needs to be plugged.

 

Is the deck slip resistant?  
Yes, all grating surfaces on the Spill Decks are slip resistant.

 

What does a t-strip do?  
The T-Strips lay across the point where two Spill Decks come together.  By “bridging the gap” this piece diverts spills to either of the Decks and keeps any spillage from getting between the units.

 

How many Bulkhead Fittings and T-strips do I need?  
One for each 26” of Spill Deck that is being connected.

 

Does the Ultra-Spill Deck’s sump capacity meet regulations?  
(Note:  The answer to this question is based on one assumption:  That the Spill Decks are being used with 55-gallon drums).  By themselves, the 2-Drum and 4-Drum Spill Deck Plus units do not meet EPA requirements.  They must be connected to an another Ultra-Spill Deck to increase the total sump capacity to 55 gallons minimum. 

 

What is the size of the grating? 
Ultra-Spill Deck Plus Models use a grating that is 52"L x 26"W x 4"H.